
Lawn mower decks can be easily damaged, but they can also be easily repaired. In this blog post, we will show you how to fix a lawn mower deck in just a few simple steps. We will also provide tips on how to prevent deck damage in the future. So, whether your lawn mower deck is damaged or not, read on for some helpful tips!
I. Bent Mower Deck
If you have a lawnmower that has a bent deck, you can straighten it back into shape. There are the seven commandments of how to fix a bent mower deck that works out instantly.
Step 1. Gather The Tools– The most important thing about this work is gathering essential tools. There are several kinds of tools we need. The tools are given below : reattached with a long handle; a socket the size of the bolt on your mower,
- A pair of channel lock pliers
- Shop rag
- Ball peen hammer
- A sledgehammer File
- Working gloves
- An anvil as you have one
Step 2. Remove The Blade Carefully From The Mower– For removing the sword from the mower, you need to flip the mower up one side. It is better to flip the mower so that the air filter is up and that the gas or oil doesn’t exist or leak into the air filter. Take a socket and a wrench to remove the blade. You will need something to brace the blade.
I generally do this with my foot. Suppose you don’t want to use your foot. You can use a hefty price of scrap wood. Put that wood between your foot and your mower blade. When the mower blades remove, flip it back over to sit on the ground as it should.
Step 3. Do Not Forget To Bend Your Bent Mower Deck– To bend the bent mower deck, you have to find a secure method. From my point of view, the best practice is to replace the none curved end under the plover and use a pair of channel locks to bend the blade back to fairly straighter and smoother.
Step 4. Hammer The Mower Deck Blade Correctly– Hammer, the mower deck blade, is a crucial thing in this work. You can choose the ball peen hammer to flatten out the last of the bend. I suggested using the anvil for this. But if you don’t want to do this, you can use access to one a sledgehammer.
Step 5. Sharpen The Bent Mower Deck– Before going through the job of how to fix a bent mower deck, sharpen the bent mower deck is a critical task. First of all, grab the file, hold the straightened blade against your work table, and sharpen the cutting edge.
Step 6. Reattach The Blade On The Mower– You have to take the straightened blade, wrench, and socket, flip the lawnmower up on its side. Then reattach the lawnmower blade. Please check the tightness of the edge.
Step 7. Do Not Forget To Paint Or Conceal To The Repair– After finishing the task of how to fix a bent mower deck, do not forget to paint or conceal to the repair. It will help sand the dent and surrounding area to get rid of any paint or hammer marks on the deck.
II. Rusty Mower Deck- Remove the rust
If you don’t get rid of the rust then there’s no point in doing the job as the whole mower will fall apart at some point so here’s where the Hammerite Kurust comes in.
Step 1. Clean the area- Ensure the area is clean from grass and dust etc and then get at it with a wire brush. This will remove any loose paint and rust and give you a sound surface to work from.
Step 2. Apply the Kurust with an old brush- The Kurust will convert the rusty area into a solid and inert surface. If you want to get geeky then it actually converts iron oxide to stable iron complexes.
Please note you shouldn’t put the brush back into the original pot as that could spoil it, so first off transfer any Kurust you intend to use into a separate pot.
Step 3. Leave it to dry and do it’s magic- It only actually takes 15 minutes so this really is a job you can do all in one go.
III. Hole in a mower deck- Repair the hole
Step 1. Cut out lengths of glass fibre into handy and workable sizes. There’s plenty in the pack so cut a lot as it gets messy later on.
Step 2. Put plastic gloves on (again supplied in the pack)
Step 3. Mix some resin with the hardener. Only make enough you can use in 5 minutes as it will set pretty quickly!
Step 4. Brush the mixed resin onto a strip of glass fibre and then put the strip onto the mower hole, sticky side down. Generously apply more resin to the fibre and stipple the brush so that you can see the fibre glass starting to separate which will indicate that it’s been fully applied.
Step 5. Repeat with the remainder of the strips allowing a slight overlap. These will fully harden in 20 minutes so if you want to apply another layer of fibre glass then you can.
How do you clean a lawn mower deck?
To clean the deck of a lawn mower, follow these steps:
Step 1. Empty the gas tank (or run the mower until the tank is empty).
Step 2. Then disconnect the spark plug wire.
Step 3. Stand the mower up on its side.
Step 4. Take a garden hose and spray the deck at full blast.
Step 5. Scrub off the rest of the soil, using a brush, soap, and hot water.
Related Questions
How to level a lawn mower deck?
The deck of a lawn mower is the surface that the blades of grass and dirt rest on. The deck is also called the cutting surface or bed.
To level your lawn mower deck, you should first start by removing any debris from the deck. Then, use a level to make sure that it is flat. If it’s not flat, then use a wrench to loosen or tighten bolts so that it is at an even height all around.
How to remove dried grass from lawn mower deck?
There are many ways to remove dried grass from lawn mower deck. One of the easiest ways is to use a shop vac. Simply attach the hose attachment to the end of the vacuum and turn it on.
It will suck up all the clippings and dry grass that are on your deck. You can also put some paper towels underneath your lawn mower deck and vacuum them up.
How to measure lawn mower deck size?
The deck size of a lawn mower will determine the size of the cut. For example, a small deck size is about 12 inches and it can cut grass up to 18 inches high.
A large deck size is about 20 inches and it can cut grass up to 24 inches high. The cost of a lawn mower is usually proportional to its deck size. The larger the deck, the higher the price tag.
How to level a husqvarna lawn mower deck?
To level a husqvarna lawn mower deck, one should loosen the bolt on the front of the deck with a hex wrench. Loosen it just enough so that the blade can be rotated. Then rotate it until it is even with the ground.
Tighten the bolt and check to make sure that it is even with all four sides of the deck. If not, repeat this process until you get an even cut across all four sides of your lawn.
How to take the deck off a craftsman riding lawn mower?
A deck is made up of two major parts: a body and a top. The body is the metal frame that supports the top, while the top is a flat metal plate that sits on the ground.
The most common way to remove the deck from a mower is to place it on its side, then remove all bolts holding it in place by turning them counterclockwise with an appropriate wrench.