Detailed Guide on How to Start a Husqvarna Lawn Mower
Detailed Guide on How to Start a Husqvarna Lawn Mower

You can keep your grass under control with lawnmowers. Despite having many leading lawnmower manufacturers on the market, Husqvarna has always been a reliable choice for gardening enthusiasts. If you have never used a Husqvarna lawnmower before, there is no need to be concerned. In this blog, you'll find all the information you need to get started with a Husqvarna lawn mower.

Step by step instructions for starting your Husqvarna lawnmower:

  1. You should check your oil, gas, battery, and spark plug
  2. Then turn the key. For a push behind the lawnmower, you get the engine going by pulling the rope three times.
  3. On riding mowers, activate the parking mode by keeping the foot brake pressed.
  4. Retract the blades by pulling back the blade engagement lever.
  5. Before starting the mower. Position the choke to the top.
  6. To start the riding lawnmower, turn the ignition key. Once it starts, turn the throttle down.

Lawnmowers can be classified into two main types, i.e., riding lawnmowers and push lawnmowers. With push mowers, you walk behind the mower to steer it in the right direction, but the mower drives itself. With a manual push-behind lawnmower, you must physically push the mower forward. In this article, we provide a simple step-by-step solution for starting your Husqvarna lawnmower.

For its customers, Husqvarna offers two types of lawnmowers: riding lawnmowers and push lawnmowers. Husqvarna lawnmowers are relatively easy to start, and you can do it by following these steps. 

● 1. Oil Check:

It is always a smart idea to check the engine's oil level before starting any lawnmower. To see the oil level, look for the black oil cap on the engine. Remove the cap and look at the dipstick to see the oil level and condition. If the oil is dark, it should be replenished.

If the oil level on the dipstick drops below the "Add" level, the engine should be refilled with the oil recommended by the manufacturer. Fill to the correct level and tighten the cap appropriately. Wipe any oil that has been spilled on the body and side.

● 2. Replace the old fuel:

It is recommended that you replace the old fuel in the tank with fresh fuel injection if your Husqvarna lawnmower has been sitting for some time. Fuel consistency declines over time, which causes deposits in the carburetor and filter. You may experience difficulty starting or stopping your engine after starting. Throw away the old fuel.

●3. Examine the spark plug: 

Your machine's spark plug is located on the front or side. It can be removed with a wrench. Wipe it gently with a cotton cloth so as not to damage the electrodes.

● 4. Check the battery:

When your Husqvarna lawn mower's battery is dead, the engine won't start. Check the battery terminals with a multimeter to see if there is any voltage there.

Husqvarna lawn mower

How to start a Riding Husqvarna lawnmower?

The following steps will explain how to start a Husqvarna riding lawnmower after you have completed the above steps.

 ● Step 1: Establish your position

Ensure that all the levers are accessible to you when starting the mower. Insert the key, but do not turn it yet.

● Step 2: Activate the parking mode

The parking mode must be activated before starting the unit. To do this, move the lever to park mode. The parking mode must be on when the mower is started, but must be deactivated when it is accelerat

● Step 3: Withdraw the blade lever

The blade lever is located on the right-hand side of the fender. Make sure it is in the 'off' position, which ensures that the blades aren't active when cutting.

● Step 4: Set the lever for the choke

Your mower's choke lever should be set to the highest position if it has one. After the lawnmower has started, you can switch it back to a position where the engine does not shut off. Also, activate the neutral gear on the front gearbox. 

● Step 5: Turn the key

Turn the ignition key to the 'Start' location for around 10 seconds before starting the engine. Once it's running, turn it back to the 'On' position.

How to start a Husqvarna Push lawnmower?

You can easily operate a Husqvarna push-behind lawnmower by following the steps below. If you are just starting, assume you haven't done it for a while. As previously explained, we always recommend that you check your fuel, oil, plugs, and batteries before starting a mower.

● Step 1: Check the spark plug wire

To check if the spark plug wire is loose, gently tug it. Push it back into place if needed.

●Step 2: Set the choke lever to the desired position

Your machine has its throttle lever in the stop position. You might find it easier to start the engine if you put the lever in the "choke" position.

● Step 3: Prime the engine

You should pull the cord on your engine three times to prime it. When you perform the maintenance pre-start measures correctly, your engine starts without any problems. Once the engine hasn't started after the third pull, you need to troubleshoot the cause.

● Step 4: Place the throttle lever at the highest position

Once the engine with the throttle handle starts running, it will run rough. To fix this, pull the throttle lever back into the 'run' position. As a result, the engine now runs smoothly.

Related Questions

1. What are the reasons for a lawnmower not starting?

Here are some likely reasons why a lawnmower will not start:

  • Inadequate fuel: The most straightforward way to troubleshoot is to check your fuel tank and fill it up if it is empty. If the fuel tank is full, you can move to the next step.
  • Defective spark plug: It is possible that the electrodes of the spark plug have been damaged or have developed carbon deposits. An engine may suffer from a loss of combustion due to this defect.
  • Bad Air Filter: Your device's air filter is located just outside and is highly prone to accumulating dust and foreign particles. As a result, the carburetor could not draw enough air to create a fuel-air mixture.
  • Clogged Carburetor: Over time, carburetor jets become restricted due to fuel deposits. In consequence, the air-fuel mixture is not adequately delivered, resulting in inefficient combustion.
  • Constricted fuel filter: 
  • Debris and dirt can also clog the fuel filter. These could also be contributing factors.

2. Where is the carburetor on a lawnmower?

Carburetors are engine components found internally, under the hood. Therefore, they are not noticeable from the outside. Disconnect the air filter and its framework from the carburetor by removing the screws and the breather hose. This would make the carburetor visible from the outside.

3. What is the best way to clean the carburetor on a lawnmower without removing it?

You can clean a lawnmower carburetor without removing it entirely from the mower's body. Below are the steps:

  • Detach the air filter housing: The air filter's housing, which contains the frame, the cover, and the air filter itself, is completely detachable from the main mower body.
  • Detach the ducts: Remove the fuel lines that connect to the carburetor. Put a secure container in front of the empty fuel tanks to hold all the depleted fuel.
  • Remove the bowl nut: Unscrew the nut on the carburetor bowl. This nut is prone to developing fuel deposits.
  • Spray the carburetor cleaner: Spray any brake or carburetor cleaner inside the carburetor to dislodge any obstruction. In addition, pass a metal wire through the bowl nut to eliminate any deposits.
  • Reassembly: As soon as you're done cleaning, you can assemble all the pieces back into the lawnmower.

4. Why does my carburetor not receive any fuel?

There are several reasons why your carburetor isn't drawing fuel. Let's investigate them one by one.

  • Check the filters: Check the fuel filter for blockages or constraints that could be hindering the intake of fuel.
  • Check the fuel lines: Make sure you check your carburetor's fuel lines for kinks and turns.
  • Inspect the carburetor: Check the carburetor to make sure the needle valve is not stuck or the float doesn't prevent fuel from entering.
  • Access the fuel pump: If your unit uses an electric fuel pump, be sure to check the fuse for the pump in the fuse box. You can examine the mechanical pump case by connecting its intake to an external fuel source, such as a gas tank. If you pump fuel from an external source, then the problem resides somewhere near your system's fuel tank. Hence, your fuel tank should be inspected.

Final Thoughts

It is important to keep in mind that lawnmowers are machines that require regular care and maintenance, much like your car. If you start the system after a long period of inactivity, you should always check the fuel and oil items. 

If it won't start, the deposits on the carburetor jets may cause low fuel quality. You may have to pay some extra money to repair the carburetor in that case, so it's better to take precautionary measures in advance. 

If it is not possible to keep cleaning the carburetor and changing the fuel repeatedly, it might be better to purchase a fuel stabilizer. Your fuel quality is typically preserved for around a year.

Leave a Reply

Your email address will not be published. Required fields are marked *